2 Ton Mini Portable Scissor Jack Car Van Vehicles Stand Tire Tool With Handle

Description

2 Ton Mini Portable Scissor Jack Car Van Vehicles Stand Tire Tool With Handle
Description：
The scissor jack, with tooth gears, can extend from
90mm(close position) to 360mm
, more than enough to lift most vehicles. Easy to operate using the chromed crank with speed handle.
Condition: Brand new
Color: Black
Minimum height: about 90MM
Maximum height: approximately 360MM
Lifting: 2.0T
Color: Black
Material: Steel
Net weight: 2.1KG
Item Size:
35*8.5*8.5 (L×W×T)
Scope: Suitable for small and medium sized vehicles. Such as: cars, Buick, Santana, Vietnam and other vehicles.
Packing include:
Scissor jack * 1+
Handle * 1
OR
Only 1 Scissor Jack
OR
Only 1 Wheel Wrench.
Attention:
1. Study, understand and follow all instructions before operating this device.
2. Do not exceed rated capacity as designated by the height/capacity curve.(Sea below)
3. Use only on hard level surface.
4. Use for emergency tire changing only.
5. Never get beneath the vehicle when it is supported by the jack.
6. Activate the hazard warning flasher,turn off ignition, set parking brake, move automatic shift selector to park position. In case of a manual transmission, move gear selector into reverse position. In addition, the wheel diagonally opposite from the wheel being lifted shall be chocked in both directions.
7. Lift only on areas of the vehicle as specified by the vehicle manufacturer.
8. Follow tire changing procedure as per the vehicle manufacturer's owner's manual.
9. No alterations shall be made to this product.
10. Failure to heed these messages may result in personal injury and/or property damage.
HEIGHT/CAPACITY CURVE
This device is designed to sustain the following loads at these specified heights. DO NOT EXCEED the rated capacity for each position.
Before Use:
1. Check before each use for abnormal conditions such as cracked welds, leaks, damaged, loose or missing parts.
2. Inspect the jack immediately if lift is believed to have been subjected to an abnormal load or shock.
3. If the jack is found to be damaged, it should be removed from service until properly repaired.
OPERATING INSTRUCTIONS:
1. Insert the jack handle into the hole of the handle socket.
2. Make sure that the saddle is correctly positioned. To prevent damage to the jack, do not move the jack while the handle is intact in the socket.
3. To raise load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle clockwise.
4. To lower load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle counterclockwise slowly.
CARE AND MAINTENANCE:
1. When jack is not in use, lifting arm should be in full down position.
2. Always keep jack clean and keep the screw and bearings well lubricated.
3. Store the handle with care.
Feedback
Payment
Delivery details
Contact us
Shipping Guide
Feedback
Payment
1.We accept PayPal only!
2.Please keep the consistency of the address from Paypal and eBay.
3
.
Payment must be received within 3 days since you won the item, or eBay will launch Unpaid Reminder Against you.
Delivery details
Sincerely thank you for choosing us, we suggest you reading our shipping terms and conditions.
1.All items are shipped within 1-2 business days after we confirm your payment and your shipping address.
2.We only ship our items to the areas that our logistics provider covers.
3.To ensure you receive item safely, please offer the concrete and complete shipping address
4.If you are in Puerto Rico,Hawaii,Alaska,APO/FPO,US Protectorates, please contact us via eBay message to discuss the shipping.
5.Please keep the consistency of the address from Paypal and eBay.
6.Sometimes your order may be impacted by extreme bad weather, strikes or other unexpected events.
7.If there are any problems with your order, including late delivery or being lost, please do not hesitate to contact us. We are happy to offer solutions to your inquiries.
Contact us
Shipping Guide